Thread Rating:
  • 144 Vote(s) - 3.09 Average
  • 1
  • 2
  • 3
  • 4
  • 5
MC424 - close automatically once open
#1
Hi,

i have installed Nice MC424 at home, (opening in direction inside), at works perfect.

I have bought the same set to my father, and configured in the same way, but does not work properly. Only difference is that at fathers home gates are configured to be opening in direction outside. But connection of wires should be the same per seller.

Gate itself works well when i stop it while opening using remote. When i hit button, it starts opening, when i hit button again while gate is moving, gate stops. When hit button again, gate will close and will remain closed.

But the problem is when i want to just open it.
In my place, the i hit the button, gate will open, will wait 20 seconds and than will close automatically.

In father house it does not work.
When i hit remote control, gate will open, but just when it will finish opening, gate will start closing automatically, without waiting 20 second.

I have put gate into factory settings, but did not solve the problem.

Any idea what might be wrong?

Marek
Reply
#2
(02-12-2017, 04:11 PM)maaarek Wrote: Hi,

i have installed Nice MC424 at home, (opening in direction inside), at works perfect.

I have bought the same set to my father, and configured in the same way, but does not work properly. Only difference is that at fathers home gates are configured to be opening in direction outside. But connection of wires should be the same per seller.

Gate itself works well when i stop it while opening using remote. When i hit button, it starts opening, when i hit button again while gate is moving, gate stops. When hit button again, gate will close and will remain closed.

But the problem is when i want to just open it.
In my place, the i hit the button, gate will open, will wait 20 seconds and than will close automatically.

In father house it does not work.
When i hit remote control, gate will open, but just when it will finish opening, gate will start closing automatically, without waiting 20 second.

I have put gate into factory settings, but did not solve the problem.

Any idea what might be wrong?

Marek

hi


if that issue will hapen again ,check diagnostic led P2 follow manual .

slow down engines speed , thats my suggestion
Best Regards 
Tom 
Automatic-TC
Reply
#3
(02-12-2017, 10:43 PM)Automatic-TC Wrote:
(02-12-2017, 04:11 PM)maaarek Wrote: Hi,

i have installed Nice MC424 at home, (opening in direction inside), at works perfect.

I have bought the same set to my father, and configured in the same way, but does not work properly. Only difference is that at fathers home gates are configured to be opening in direction outside. But connection of wires should be the same per seller.

Gate itself works well when i stop it while opening using remote. When i hit button, it starts opening, when i hit button again while gate is moving, gate stops. When hit button again, gate will close and will remain closed.

But the problem is when i want to just open it.
In my place, the i hit the button, gate will open, will wait 20 seconds and than will close automatically.

In father house it does not work.
When i hit remote control, gate will open, but just when it will finish opening, gate will start closing automatically, without waiting 20 second.

I have put gate into factory settings, but did not solve the problem.

Any idea what might be wrong?

Marek

hi


if that issue will hapen again ,check diagnostic led P2 follow manual .

slow down engines speed , thats my suggestion

Hi Automatic-TC,

it is always with this incorrect behavior. I will check it tomorrow with lower speed and diagnostics.
When exactly i should see diagnostic led blinking? Once system is restarted? Or how to enter diagnostic menu? Or do i undestand it correctly that i should be watching this diagnostic led (P2) during opening of Gate?

One additional question. I understand others, but any idea what does it mean in manual in diagnostic section "M1/2 current sensitivity device triggering"?

Marek
Reply
#4
(02-12-2017, 11:06 PM)maaarek Wrote:
(02-12-2017, 10:43 PM)Automatic-TC Wrote:
(02-12-2017, 04:11 PM)maaarek Wrote: Hi,

i have installed Nice MC424 at home, (opening in direction inside), at works perfect.

I have bought the same set to my father, and configured in the same way, but does not work properly. Only difference is that at fathers home gates are configured to be opening in direction outside. But connection of wires should be the same per seller.

Gate itself works well when i stop it while opening using remote. When i hit button, it starts opening, when i hit button again while gate is moving, gate stops. When hit button again, gate will close and will remain closed.

But the problem is when i want to just open it.
In my place, the i hit the button, gate will open, will wait 20 seconds and than will close automatically.

In father house it does not work.
When i hit remote control, gate will open, but just when it will finish opening, gate will start closing automatically, without waiting 20 second.

I have put gate into factory settings, but did not solve the problem.

Any idea what might be wrong?

Marek

hi


if that issue will hapen again ,check diagnostic led P2 follow manual .

slow down engines speed , thats my suggestion

Hi Automatic-TC,

it is always with this incorrect behavior. I will check it tomorrow with lower speed and diagnostics.
When exactly i should see diagnostic led blinking? Once system is restarted? Or how to enter diagnostic menu? Or do i undestand it correctly that i should be watching this diagnostic led (P2) during opening of Gate?

One additional question. I understand others, but any idea what does it mean in manual in diagnostic section "M1/2 current sensitivity device triggering"?

Marek

hi

watch control board all time than hit the button .. i think that could by amperometric issue with engine . slowing down engine speed should help

regards
Tom
Best Regards 
Tom 
Automatic-TC
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Nice RB600 - Automatic close fail and opening issues P100D 1 762 30-09-2024, 02:43 PM
Last Post: P100D
  MC424 PhotoCell Bypass for Constant Power AdamG 0 503 29-06-2024, 02:45 PM
Last Post: AdamG
  Nice MCA1 stuck open after stop command Khooke 1 3,673 25-09-2023, 10:47 AM
Last Post: Michael
  Nice Robus Don't Auto Close!!!! Ali_1982 1 4,912 03-08-2022, 02:23 PM
Last Post: Michael
  Auto close and hold open kensuth 1 4,970 14-03-2022, 11:49 AM
Last Post: JoeF
  MC424 install WI-FI Switch dreqonline 6 12,449 07-03-2022, 11:05 AM
Last Post: JamieF
  Installing Nice photo sensors MC424 polomint 14 48,287 29-03-2021, 06:28 PM
Last Post: pembers
  Mc824h hold open Simonizzy 2 19,398 20-07-2020, 10:00 AM
Last Post: RyanB
  Mag-lock not activating after close benkay 0 3,709 17-02-2020, 11:39 AM
Last Post: benkay
  NIce Aria 400 unable to program gate open/close Telboy 2 12,179 13-01-2020, 03:33 PM
Last Post: Telboy

Forum Jump:


Users browsing this thread: 1 Guest(s)