Thread Rating:
  • 297 Vote(s) - 2.79 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Gate closing but not opening
#1
Question 
Hi, I have a BFT Sliding Automatic gate with Deimos motor using Mitto fobs for remote opening / closing. Installed about 5 years ago. Gate is opening but not closing. It moves about 6 inches back to close and then gets stuck ? What should I check or look for please ? Simple instructions please I'm a woman ! ALL advice very Smile welcome.
Reply
#2
Hi,
9 times out of 10 this kind of problem is down to one of the safety inputs i.e. photocells, disabling the control panel from operating. First thing to do is check the relay photocells, and that you can hear the relay tick when you pass your hand in front of the infra red beam. If you do not hear a tick, then the chances are that the relay is already being held open down to either a damaged cell or a build up of muck in the lens cover.
If you find to have faulty cells, then it is recommended to replace these asap. You can find an ideal replacement set at the following address:

http://easygates.co.uk/product_info.asp?ProductID=136

If this test does not prove to be successful, then you will need to take a look at the control panel and run through the diagnostics from the manual on there to see if there is anything else affecting the system.

Kindest Regards,
Dave

(11-06-2014, 11:17 PM)CAROL Wrote: Hi, I have a BFT Sliding Automatic gate with Deimos motor using Mitto fobs for remote opening / closing. Installed about 5 years ago. Gate is opening but not closing. It moves about 6 inches back to close and then gets stuck ? What should I check or look for please ? Simple instructions please I'm a woman ! ALL advice very Smile welcome.
Dave Blake

EasyGates.co.uk - EasyGates Ltd | EasyGates Direct - Trade only accounts | Smart and Secure Center - Smart Home Products
Reply
#3
Thank you Dave. Will try and let you know.

(12-06-2014, 09:26 AM)Blakey111 Wrote: Hi,
9 times out of 10 this kind of problem is down to one of the safety inputs i.e. photocells, disabling the control panel from operating. First thing to do is check the relay photocells, and that you can hear the relay tick when you pass your hand in front of the infra red beam. If you do not hear a tick, then the chances are that the relay is already being held open down to either a damaged cell or a build up of muck in the lens cover.
If you find to have faulty cells, then it is recommended to replace these asap. You can find an ideal replacement set at the following address:

http://easygates.co.uk/product_info.asp?ProductID=136

If this test does not prove to be successful, then you will need to take a look at the control panel and run through the diagnostics from the manual on there to see if there is anything else affecting the system.

Kindest Regards,
Dave

(11-06-2014, 11:17 PM)CAROL Wrote: Hi, I have a BFT Sliding Automatic gate with Deimos motor using Mitto fobs for remote opening / closing. Installed about 5 years ago. Gate is opening but not closing. It moves about 6 inches back to close and then gets stuck ? What should I check or look for please ? Simple instructions please I'm a woman ! ALL advice very Smile welcome.
Reply
#4
Hi Dave

Problem solved. It was the spring that was disengaging from the bent "arm"....thank you for your help...Smile



(12-06-2014, 09:26 AM)Blakey111 Wrote: Hi,
9 times out of 10 this kind of problem is down to one of the safety inputs i.e. photocells, disabling the control panel from operating. First thing to do is check the relay photocells, and that you can hear the relay tick when you pass your hand in front of the infra red beam. If you do not hear a tick, then the chances are that the relay is already being held open down to either a damaged cell or a build up of muck in the lens cover.
If you find to have faulty cells, then it is recommended to replace these asap. You can find an ideal replacement set at the following address:

http://easygates.co.uk/product_info.asp?ProductID=136

If this test does not prove to be successful, then you will need to take a look at the control panel and run through the diagnostics from the manual on there to see if there is anything else affecting the system.

Kindest Regards,
Dave

(11-06-2014, 11:17 PM)CAROL Wrote: Hi, I have a BFT Sliding Automatic gate with Deimos motor using Mitto fobs for remote opening / closing. Installed about 5 years ago. Gate is opening but not closing. It moves about 6 inches back to close and then gets stuck ? What should I check or look for please ? Simple instructions please I'm a woman ! ALL advice very Smile welcome.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Deimos ultra bt a400 Gate to stay open Sootylfc 0 175 04-11-2024, 05:59 PM
Last Post: Sootylfc
  Deimos ultra bt a400 gate - not working with fobs Sootylfc 2 566 15-10-2024, 10:37 AM
Last Post: Sootylfc
  BFT LUX G BT 2B gate won't open or close fully PaulR 1 968 17-07-2024, 02:24 PM
Last Post: benbrooks
  BFT Sliding Gate randomly opening and closing AdrianMate 5 4,254 14-06-2024, 12:12 PM
Last Post: JoeF
  Gate radio receiver not working Zhymke 0 660 23-05-2024, 06:35 PM
Last Post: Zhymke
  Gate wont close issue MR_ROBOT 3 11,562 11-04-2024, 08:08 AM
Last Post: JoeF
  Bft gate problem djkokalis 1 2,682 14-02-2024, 12:39 PM
Last Post: JoeF
  BFT Rigel 4 - single Gate Not Closing Tsnash 1 2,358 04-01-2024, 10:21 AM
Last Post: JoeF
  BFT sliding gate intermittent operation vozm100 5 3,859 02-10-2023, 09:08 AM
Last Post: Michael
  BFT opening problem 8 48,440 08-08-2023, 02:14 PM
Last Post: JoeF

Forum Jump:


Users browsing this thread: 4 Guest(s)